Oil rig drills into salt mine video

In , the formation of a often pushes terrain upward from the surrounding land, while also creating a subterranean , holding petroleum deposits. On Thursday, November 20, 1980, the drill assembly of a contracted , just offshore of the salt dome-caused Jefferson Island (itself in the east southeast section of Lake Peigneur), pierced an inactive third level of the . The hole produce. [pdf]

FAQS about Oil rig drills into salt mine video

Why did 12 men abandon their oil drilling rig?

Early in the morning on November 20, 1980, twelve men decided to abandon their oil drilling rig on the suspicion that it was beginning to collapse beneath them. They had been probing for oil under the floor of Lake Peigneur when their drill suddenly seized up at about 1,230 feet below the muddy surface, and they were unable to free it.

Did a drill crew Penetrate the salt dome?

Clearly, the salt dome which contained the mine had been penetrated by the drill crew on the lake.

What happened at the bottom of a ruined salt mine?

Trapped air geisered upped hundreds of feet high, some of the swallowed barges floated back up to the surface, but the oil rigs, buildings, salt-filled barges, and other equipment are still at the bottom of a ruined salt mine. The experience gave Richard nightmares for years.

Down-the-hole drill installation and debugging video

A down-the-hole drill, usually called DTH by most professionals, is basically a screwed on the bottom of a . The fast hammer action breaks hard rock into small cuttings and dust that are evacuated by a fluid (air, water or ). The DTH hammer is one of the fastest ways to drill hard rock. The system is thought to have been invented independently by Stenuic. [pdf]

FAQS about Down-the-hole drill installation and debugging video

What is a down-the-hole drill?

A down-the-hole drill, usually called DTH by most professionals, is basically a jackhammer screwed on the bottom of a drill string. The fast hammer action breaks hard rock into small cuttings and dust that are evacuated by a fluid (air, water or drilling mud). The DTH hammer is one of the fastest ways to drill hard rock.

What is down-the-hole (DTH) drilling?

Down-the-hole (DTH) drilling has made it easier for contractors to drill wells faster and more efficiently, and to transition from dirt boring to rock boring just by adding a compressor and hammer to the drill bit.

How does DTH drilling work?

With DTH drilling, contractors can change the drill that they were using for the current directional bore to a rock drill when they encounter rock by connecting the drill with a compressor and a steerable hammer. Well drilling also needed changes to be made to rotary drilling when the well needed to take a turn.

How does DTH hammer drilling work?

A flushing current conveys the loosened drill cuttings upwards and exits at the upper end of the casing. If you have any further questions, please contact our local sales or service team. DTH hammer drilling is a percussive drilling process powered by compressed air.

What is a DTH drill?

DTH is short for “down-the-hole”. Since the DTH method was originally developed to drill large-diameter holes downwards in surface-drilling applications, its name originated from the fact that the percussion mechanism followed the bit down into the hole.

How do you drill a rock with a DTH hammer?

This method is mainly applied for hard to very hard rock and/or for penetrating large boulders. 1. Setting the DTH hammer with drill rod and casing on the drilling point. 2. Rotary and percussive drilling of the drill string under compressed air supply. 3. After reaching the final depth, unlocking of the drill rod with DTH hammer and pilot bit.

Drilling video of a small down-the-hole drill

A down-the-hole drill, usually called DTH by most professionals, is basically a screwed on the bottom of a . The fast hammer action breaks hard rock into small cuttings and dust that are evacuated by a fluid (air, water or ). The DTH hammer is one of the fastest ways to drill hard rock. The system is thought to have been invented independently by Stenuic. [pdf]

FAQS about Drilling video of a small down-the-hole drill

What is a down-the-hole drill?

A down-the-hole drill, usually called DTH by most professionals, is basically a jackhammer screwed on the bottom of a drill string. The fast hammer action breaks hard rock into small cuttings and dust that are evacuated by a fluid (air, water or drilling mud). The DTH hammer is one of the fastest ways to drill hard rock.

What is down-the-hole (DTH) drilling?

Down-the-hole (DTH) drilling has made it easier for contractors to drill wells faster and more efficiently, and to transition from dirt boring to rock boring just by adding a compressor and hammer to the drill bit.

What is a DTH drill rig?

A down-the-hole drill, usually called DTH Drilling Rig, is basically a mini jackhammer screwed on the bottom of a drill string. The speedy hammer activity breaks hard stone into little flakes and dust and can be dismissed evident by the air exhaust in the DTH hammer.

How long did it take to drill a 12,000 ft hole?

The original estimate for completion of a 12,000-foot hole was 30 days using the conventional rotary technique, which was reduced to 13 days using the DTH method. Before DTH was used, drillers would typically case the vertical portion of the well and convert to rotary drilling to drill at a tangent.

How was a hole drilled?

This system could not guarantee a finished hole size and only pure vertical holes could be drilled as the system basically relied on gravity. Debris from the hole was baled out using a baling tube with a clack valve, which was periodically dropped on a winch to capture the slurry, which was then brought to the top of the hole to be discharged.

How does a drill work?

This action along with the rotational movement of the drill string crushes the rock efficiently. Since the piston strikes directly on the bit, energy transfer takes place down the hole with minimum loss of energy, allowing drilling to greater depths. The driving medium i.e. compressed air is also the flushing medium.