Raising procedure for ideco hfr 142 1000 drilling rig

Raise the bottom of the mast to the rig floor and pin it in place. Raise the crown section into place on the derrick stand. Raise the "A-legs" and pin them into place. Pin the monkeyboard in place on the mast. Lay out all lines and cables to prevent tangling when the mast is raised. [pdf]

FAQS about Raising procedure for ideco hfr 142 1000 drilling rig

How much does an Ideco 1000 hp rig cost?

IDECO 1000 HP DRILLING RIG (Ref#9965Tb) Manufactured 2004, 117’ SHL telescoping mast, mounted on 3 axle, 358,000# static hook load, 5-sheave travel block, racking board, mounted on 3 axle trailer, optional 250 ton top drive/power swivel Price as is: $700,000 Price reworked cleaned, painted and certified: $1,300,000

How much does an Ideco H44 drill rig cost?

IDECO H44 DRILL RIG (Ref#3977T) 1000 hp trailer mounted drill rig, (2) Detroit 60 Series engines 475 hp each @ 1800 rpm, 117’ x 450,000# derrick, 17’ adjustable substructure, Century 17-1/2” x 44” rotary tble, National 160 ton Shorty block, V door catwalk, water tank/doghouse combo Price: $275,000

How should a rig rig be secured before raising a mast?

Be sure the derrick escape device is in place and the line is properly secured to the mast before raising the mast. All rig floor winch lines, tong hanger lines, etc., should be secure to prevent them from getting tangled with the blocks as the mast is raised.

How much does a Ideco H37 rig cost?

IDECO H37 WELL SERVICE RIG (Ref#1683RR) 103' x 244,000# franks telescoping hydraulically raised mast, Detroit Series 60 diesel engine, Allison 5860 transmission, mounted on 5 axle carrier, hyd leveling jacks, hyd utility hoist, air and hyd controls, front flotation tires Price: $245,000

How much does a 1000 hp drill rig cost?

IDECO 1000HP DRILLING RIG (Ref#11167N) Single drum drawworks, 1-1/8" drilling line, hydramatic brake, 2 engine compound (2) Detroit Series 60 diesel engine 550 hp each (drives rig and carrier), 112' x 378,000# mast, 8 lines, 16' substructure, mounted on 6 axle carrier, (2) 6061 Allison transmission, No additional equipment Price: $825,000

How much does a dreco H44 rig cost?

IDECO H44 DRILL RIG (Ref#3981T) Drive in, rated to 6500’ with 4-1/2” drill pipe, (2) Detroit 871 engines (305 hp each), Ideco 108’ x 268,000# mast, 12’ H telescoping substructure, Dreco 150 ton block, ZP 17-1/2” x 44” rotary table, V-door catwalk, water tank/doghouse combo Price: $215,000

Rotary drilling rig process

A rotary drilling rig works by rotating a drill string, which applies downward pressure to a drill bit that grinds the earth. Drilling fluid or air is pumped down the drill string to cool the bit, carry cuttings to the surface, and stabilize the borehole. [pdf]

Jack up rig drilling process

Jackup rigs are so named because they are self-elevating with three, four, six and even eight movable legs that can be extended (“jacked”) above or below the hull. Jackups are towed or moved under self propulsion to the site with the hull lowered to the water level, and the legs extended above the hull. The hull is actually a water-tight barge that floats on the water's surface. When the rig reaches the work site, the crew jacks the legs downward through the water and int. [pdf]