BRISBANE NEWS SUBCONTRACTOR FIGHTING FOR LIFE ANOTHER INJURED

Drilling rig accident brisbane

Drilling rig accident brisbane

Two workmen have narrowly missed being crushed by construction machinery after it collapsed in Brisbane’s north this afternoon. Video obtained by 9NEWS showed the men turning their backs to the Newstead construction site when a large drilling rig suddenly toppled over. [pdf]

FAQS about Drilling rig accident brisbane

What happened to the overburden drill?

The mast of the drill was in a raised position at around 25 degrees off vertical. Two drill maintainers arrived at the overburden drill to inspect and repair a reported oil leak. In preparation for the repair the drill was washed, lowered off its three hydraulic levelling jacks, refuelled and the hydraulic tank refilled.

Why did the operator drill a hole in an overburden drill?

The operator completed drilling a hole as per design when machine sensors detected low hydraulic oil level. The mast of the drill was in a raised position at around 25 degrees off vertical. Two drill maintainers arrived at the overburden drill to inspect and repair a reported oil leak.

What happened to a 67-year-old rig operator?

The 67-year-old operator suffered a compound fracture to his leg while jumping clear of the rig as it fell. The company was barred from using the rig and excavator, which were both damaged in the accident. "Two prohibition notices were issued and subsequently complied with," a Workplace Health and Safety Queensland spokesperson said.

Is there a risk assessment for the use of the drill?

No operational risk assessment for the use of the drill was identified. There was no working visible manual level bubble fitted. The drill had been involved in a rollover five years prior. Following this incident grade alarms were fitted to the drill.

What happened at a Brisbane worksite?

A man is fighting for life and another is injured after they were struck by a metal object at a Brisbane worksite. Paramedics were called to the CavCorp development site on Wyandra Street in Newstead at 12.10pm (1.10pm AEDT)today after a metal object fell from a piece of machinery.

What happened at a deck handrail drill?

The operator and one maintainer exited the drill safely. The other maintainer was trapped between the deck handrail and the light vehicle parked beside the drill. An emergency was initiated, and the Emergency Response Team (ERT) assisted with the safe recovery of the trapped maintainer. How did it happen? Events leading up to the incident

Half life 2 highway 17 drill rigs

Half life 2 highway 17 drill rigs

You'll start this chapter by emerging from inside the warehouse's back room into a large loading area with a crane and your new vehicle, the car! To begin with, hop in and the woman in the crane will lower yo. [pdf]

FAQS about Half life 2 highway 17 drill rigs

How do you fight a Combine in Half-Life 2?

This section of the larger Half-Life 2 walkthrough will cover your efforts to fight the Combine occupying the second base. You'll have to kill a large number of soldiers and use a crane to carry your car across the gap. If you are stuck on any part f this phase, then just look inside for a little help.

How do I get to Sandtraps in Half Life 2?

Once past, drive off the bank to the left of the bridge, under the old bridge section, up the ramp and into the tunnel. Around the corner, you'll get another loading screen, and enter the next chapter - Sandtraps. Welcome to Highway 17, the seventh level of Half Life 2.

How do you use a buggy in Half-Life 2?

The buggy drives with your direction keys: straight goes forward, back goes in reverse, left turns left, and right turns right. The mouse is used to look around and aim the tau cannon (basically the gauss gun from Half-Life 1). Fire it with the primary attack button and charge with the secondary.

How do you get through a roadblock in Chapter 17?

Take down this forcefield to move on. Pin a soldier to the billboard in chapter Highway 17. Follow the road along past the various abandoned cars until you reach another roadblock ahead of a large Combine outpost complete with a forcefield that will stop you passing through. Clear the roadblock first of all, but leave you car back here.

Screw air compressor oil life

Screw air compressor oil life

However, to extend the compressor's lifespan, you must change the oil more often (every 4,000 hours) and draw an oil sample every 1,000 hours. Oil plays a crucial role in the life of an oil-lubricated rotary screw air compressor: Removing impurities. [pdf]

Power Your Operations With Reliable Mining Equipment?

We are a leading manufacturer of drilling rigs and air compressors for mining and construction industries.