Aker barents drilling rig

There was previously in the 1970s a different company called Aker Drilling, also part of the Aker Group, which later became part of . The history of the 2005 established Aker drilling is as follows; Aker drilling was established in 2005, as part of the controlled by the Norwegian billionaire . The purpose of the new company was t. [pdf]

FAQS about Aker barents drilling rig

Are Aker BP & Equinor drilling in the Barents Sea?

Aker BP and Equinor have completed drilling operations in the Barents Sea, which was recently expanded with new acreage in APA 2024.

What is a Transocean Barents drilling rig?

The drilling rig Transocean Barents is designed to operate in tough environments and at water depths of 3000 metres. The type ‘H6e’ drilling rig is a sixth-generation, semi-submersible, DP3 rig designed for global operation in ultra-deep waters. The hull section of the rig was built at the Dubai Drydocks in Dubai.

Who built the Transocean Barents drilling rig?

The top side and complete rig was built by Stord shipyard in Norway. The Transocean Barents started drilling in 2009 for oil and gas on the Norwegian continental shelf. During its operating history, it has also been called the Aker Barents. Wärtsilä supplied to the drilling rig thrusters motors, transformers, VSDs and switchboards.

Did Aker BP find a gas in the Barents Sea?

While Aker BP’s drilling efforts led to a gas discovery, Equinor had no such luck as its well was dry. The Norwegian Offshore Directorate (NOD) has confirmed a gas discovery in wildcat well 7324/8-4 (Hassel) in the Barents Sea, around 300 kilometers from the northern coast of Norway.

Who owns Aker Drilling?

Aker Drilling, was a Norwegian drilling rig operation company; based in Stavanger, Norway and majority owned by the Aker Group. It was listed on Oslo Stock Exchange under the ticker - 'AKD'.

Drilling land rig

A drilling rig is an integrated system that , such as oil or water wells, or holes for and other construction purposes, into the earth's subsurface. Drilling rigs can be massive structures housing equipment used to drill , , or natural gas extraction wells, or they can be small enough to be moved manually by one person and such are called . Drilling rigs can s. [pdf]

Parts of drill rig

Drilling derricks and Rig Masts consist of a steel framework with a square or rectangular cross-section. Their purpose is to support the hoisting equipment and rack the tubulars while tripping pipe. The number of joints in a stand (single-double-triple) that the rig can pull is dependent on the height of the derrick. . The Drawworks is one of the most important components of the drilling rig (types of drilling rigs). The unit supplies the hoisting power, the. . The Crown Blockas a drilling rig component is a fixed set of pulleys (called sheaves) located at the top of the derrick or mast, where the drilling line is threaded. The companion blocks to these pulleys are the traveling blocks. By using two sets of blocks in this fashion,. . The Traveling Blockis a set of sheaves (pulleys) that move up and down in the derrick. The drilling line is threaded (reeved) over the. . Attached to the bottom of the traveling blocks, the hook is required to hang the swivel and rig kelly(for drilling) and the elevator bales (for tripping pipe and casing). . • (#22) is a section of large diameter pipe fitted to the top of the that the attaches to via a side outlet, to allow the to flow back to the .• (BOPs) (#23 and #24) are devices installed at the wellhead to prevent fluids and gases from unintentionally escaping from the . #23 is the annular (often referred to as Hydril named after a manufacturer), and #24 is the pipe rams and blind rams. [pdf]

FAQS about Parts of drill rig

What are the components of a drilling rig?

1. Mast or Derrick Usually the first component of the drilling rig people notice, the mast is a tall fabricated structure towering above all the other drilling components. The mast is vitally important, as it supports the components of the drilling mechanism hovering above the point where drilling will take place.

How many systems are there on a drilling rig?

There are 4 main systems on a drilling rig: Ac-Dc Power Generation Station Example: Drilling derricks and Rig Masts consist of a steel framework with a square or rectangular cross-section. Their purpose is to support the hoisting equipment and rack the tubulars while tripping pipe.

How does a drilling rig work?

The drilling line spools out under gravity and is reeled in by an electrical or diesel engine. The Crown Block as a drilling rig component is a fixed set of pulleys (called sheaves) located at the top of the derrick or mast, where the drilling line is threaded. The companion blocks to these pulleys are the traveling blocks.

What is a drilling rig mast?

Usually the first component of the drilling rig people notice, the mast is a tall fabricated structure towering above all the other drilling components. The mast is vitally important, as it supports the components of the drilling mechanism hovering above the point where drilling will take place. 2. Drilling Line

What is an offshore drilling rig?

Offshore drilling rigs have similar elements, but are configured with a number of different drilling systems to suit drilling in the marine environment. The equipment associated with a rig is to some extent dependent on the type of rig but typically includes at least some of the items listed below.

How many brake systems does a drill rig have?

On most rigs, there are at least two brake systems. stop. a loaded traveling block, but is not capable of bringing it to a complete stop. An integral part of the drawworks is the gear system. This gives the driller a wide choice of speeds for hoisting the drillstring. two catheads.