RAISING AND LOWERING THE MAST
Raising procedure for ideco hfr 142 1000 drilling rig
Raise the bottom of the mast to the rig floor and pin it in place. Raise the crown section into place on the derrick stand. Raise the "A-legs" and pin them into place. Pin the monkeyboard in place on the mast. Lay out all lines and cables to prevent tangling when the mast is raised. [pdf]FAQS about Raising procedure for ideco hfr 142 1000 drilling rig
How much does an Ideco 1000 hp rig cost?
IDECO 1000 HP DRILLING RIG (Ref#9965Tb) Manufactured 2004, 117’ SHL telescoping mast, mounted on 3 axle, 358,000# static hook load, 5-sheave travel block, racking board, mounted on 3 axle trailer, optional 250 ton top drive/power swivel Price as is: $700,000 Price reworked cleaned, painted and certified: $1,300,000
How much does an Ideco H44 drill rig cost?
IDECO H44 DRILL RIG (Ref#3977T) 1000 hp trailer mounted drill rig, (2) Detroit 60 Series engines 475 hp each @ 1800 rpm, 117’ x 450,000# derrick, 17’ adjustable substructure, Century 17-1/2” x 44” rotary tble, National 160 ton Shorty block, V door catwalk, water tank/doghouse combo Price: $275,000
How should a rig rig be secured before raising a mast?
Be sure the derrick escape device is in place and the line is properly secured to the mast before raising the mast. All rig floor winch lines, tong hanger lines, etc., should be secure to prevent them from getting tangled with the blocks as the mast is raised.
How much does a Ideco H37 rig cost?
IDECO H37 WELL SERVICE RIG (Ref#1683RR) 103' x 244,000# franks telescoping hydraulically raised mast, Detroit Series 60 diesel engine, Allison 5860 transmission, mounted on 5 axle carrier, hyd leveling jacks, hyd utility hoist, air and hyd controls, front flotation tires Price: $245,000
How much does a 1000 hp drill rig cost?
IDECO 1000HP DRILLING RIG (Ref#11167N) Single drum drawworks, 1-1/8" drilling line, hydramatic brake, 2 engine compound (2) Detroit Series 60 diesel engine 550 hp each (drives rig and carrier), 112' x 378,000# mast, 8 lines, 16' substructure, mounted on 6 axle carrier, (2) 6061 Allison transmission, No additional equipment Price: $825,000
How much does a dreco H44 rig cost?
IDECO H44 DRILL RIG (Ref#3981T) Drive in, rated to 6500’ with 4-1/2” drill pipe, (2) Detroit 871 engines (305 hp each), Ideco 108’ x 268,000# mast, 12’ H telescoping substructure, Dreco 150 ton block, ZP 17-1/2” x 44” rotary table, V-door catwalk, water tank/doghouse combo Price: $215,000
Mast in drilling rig
The mast is normally used on land drilling rig types requiring a good deal of mobility; they are rarely used on offshore rigs. The racking board is in a cantilever position and lengths of drill pipeare racked on a floor, called the setback, that is separate from the mast structure. Most masts have one side open (window side),. . There are different types of masts for land drilling and service rigs: 1. Folding Type 2. Telescopic Masts 3. Bootstrap Type 4. Portable/Cantilivered masts (Non-Guy line) . Figure 8 shows a telescopic mast. Telescopic masts with their drawworks and engines are usually mounted on trucks or trailers. The load should be borne by hydraulic or. . Each structure shall be rated for the following applicable loading conditions. The following ratings do not include any allowance for impact. Acceleration, impact, setback, and wind loads will reduce the rated static hook load capacity. Technical specifications are identical to those for derricks: 1. Maximum hook load given the reeving system, 2. F. . For conventional Mast (Land rig), the below pictures show the erection sequence of rigging up For rigging up the vertical mast, the below pictures show the bootstrap sequence of rigging up. [pdf]