Raising procedure for ideco hfr 142 1000 drilling rig

Raise the bottom of the mast to the rig floor and pin it in place. Raise the crown section into place on the derrick stand. Raise the "A-legs" and pin them into place. Pin the monkeyboard in place on the mast. Lay out all lines and cables to prevent tangling when the mast is raised. [pdf]

FAQS about Raising procedure for ideco hfr 142 1000 drilling rig

How much does an Ideco 1000 hp rig cost?

IDECO 1000 HP DRILLING RIG (Ref#9965Tb) Manufactured 2004, 117’ SHL telescoping mast, mounted on 3 axle, 358,000# static hook load, 5-sheave travel block, racking board, mounted on 3 axle trailer, optional 250 ton top drive/power swivel Price as is: $700,000 Price reworked cleaned, painted and certified: $1,300,000

How much does an Ideco H44 drill rig cost?

IDECO H44 DRILL RIG (Ref#3977T) 1000 hp trailer mounted drill rig, (2) Detroit 60 Series engines 475 hp each @ 1800 rpm, 117’ x 450,000# derrick, 17’ adjustable substructure, Century 17-1/2” x 44” rotary tble, National 160 ton Shorty block, V door catwalk, water tank/doghouse combo Price: $275,000

How should a rig rig be secured before raising a mast?

Be sure the derrick escape device is in place and the line is properly secured to the mast before raising the mast. All rig floor winch lines, tong hanger lines, etc., should be secure to prevent them from getting tangled with the blocks as the mast is raised.

How much does a Ideco H37 rig cost?

IDECO H37 WELL SERVICE RIG (Ref#1683RR) 103' x 244,000# franks telescoping hydraulically raised mast, Detroit Series 60 diesel engine, Allison 5860 transmission, mounted on 5 axle carrier, hyd leveling jacks, hyd utility hoist, air and hyd controls, front flotation tires Price: $245,000

How much does a 1000 hp drill rig cost?

IDECO 1000HP DRILLING RIG (Ref#11167N) Single drum drawworks, 1-1/8" drilling line, hydramatic brake, 2 engine compound (2) Detroit Series 60 diesel engine 550 hp each (drives rig and carrier), 112' x 378,000# mast, 8 lines, 16' substructure, mounted on 6 axle carrier, (2) 6061 Allison transmission, No additional equipment Price: $825,000

How much does a dreco H44 rig cost?

IDECO H44 DRILL RIG (Ref#3981T) Drive in, rated to 6500’ with 4-1/2” drill pipe, (2) Detroit 871 engines (305 hp each), Ideco 108’ x 268,000# mast, 12’ H telescoping substructure, Dreco 150 ton block, ZP 17-1/2” x 44” rotary table, V-door catwalk, water tank/doghouse combo Price: $215,000

Moonpool drilling rig

A moon pool is an equipment deployment and retrieval feature used by , , , , and or , and. . The Hughes was a 50,500 long tons (51,300 t), 619-foot-long (189 m) ship constructed by the United States in the early 1970s for the from the Pacific seabed. The desig. . Very deep moon pools are used in —submerged chambers used by divers engaged in underwater research, , , and . In this case, shown in part D of. . Moon pools are becoming increasingly used on to allow for hauling of the gear in worse weather conditions. They also reduce the exposure of fish to air, improving quality. Along with bird scarin. [pdf]

Elevator drilling rig

Drill pipe elevators for USC with taper shoulder and square shoulder weld-on tool joints shall have bore dimensions as specified in Table 1. Notes on Table 1: Oilfield elevators with identical bores are the same. 1. * Not Manufactured. 2. ** Obsolescent connection. 1. 1 Dimension DTE from API Spec. 7, Table 4.2 2. 2. . A very close fit of the hinge pin and pawl significantly affects the correct functioning of an elevator – especially the center-latch elevator. If there is play in the hinge, the elevator tends to. . In addition to the side-door elevator, single-joint and slip-type casings are used in running casing. We use a single-joint elevator (Figure 7) to. . Since both care and inspection procedures depend primarily upon the amount of service the equipment has had, it is challenging to project. . The following checks apply to all types of elevators. For a quick reference to critical points of the drill pipe elevators, see Figure 29. 1. Is the oilfield elevator size correct? 2. Are the dies of slip-type elevators sharp? 3. Are the hinge pin or holes worn? 4. Are. [pdf]